How To Install A Moen Ex75c Garbage Disposal

Whether your electric current garbage disposal is on the fritz or simply lacks the oomph you demand to make your kitchen a perfect place, yous're in luck. Replacing a garbage disposal is a simple, do-it-yourself project that y'all tin consummate in an hour or so. Yous'll go from a not working or low-performing unit to a high-powered, make-new disposal in your kitchen in no fourth dimension at all!

Every bit a note, this guide will assist y'all supersede a garbage disposal that has a traditional plug for power. There are simply iv steps to remove and old disposal unit and 7 steps to install a new one. It actually is that unproblematic.

Tools you'll need: Hammer, adjustable crescent wrench, phillips or flathead screwdriver, wooden dowel or steel punch, plumber'southward putty (if installing a new drain flange).

Footstep 1: Turn off the electricity

Find your billow box and cutting the excursion breaker that provides power to the plug that your disposal plugs into under your sink. This is for your safety as well equally safety of your new unit. This will too ensure that power to your dishwasher is off if you have a dishwasher.

Step ii: Disconnect the bleed tube

Utilize a wrench to disconnect the drain line where information technology connects to the disposal discharge tube.

Step 3: Loosen the fastening hardware

Your current garbage disposal will have bolts connecting your drain to the acme of the garbage disposal unit of measurement. Loosen these using a screwdriver.

Step 4: If y'all take a dishwasher, remove the discharge hose

Side by side, if yous have a dishwasher, you'll need to loosen the clamp that connects the dishwasher discharge hose to the disposal unit. Simply utilise your screwdriver for this likewise.

Step 5: Remove the one-time disposal unit

Note: Yous'll either demand a second set of hands or want to prop a box under the unit to support it when it comes loose from the drain.

Locate the three-tab ring where the acme of your onetime disposal unit joins with the bleed. Using either your easily or a screwdriver inserted into one of the 3 tabs, rotate the ring counterclockwise until the old unit releases from the bleed. Voila! Your old garbage disposal has been removed. You're now ready to install your new garbage disposal.

Step 1: Determine if you lot demand a new drain assembly

When you replace a garbage disposal you might exist able to use the drain associates that's already installed from your previous unit of measurement. If that's the case, excellent!

If you need to replace the drain assembly, remove the current assembly and then clean the sink surface thoroughly. Make certain it's dry. And so, apply a i/two" thick band of plumber's putty around the ring and press into identify.

Now, place the new drain assembly into the sink, centering it in the bleed opening. To make a tight seal, place the new garbage disposal unit of measurement on top of the drain associates to press it into place while you go along working.

Stride 2: Accept apart the mounting assembly

Before you brainstorm this step, be sure to take note of the order the pieces go in on the mounting assembly. We recommend placing them on the flooring in the order y'all took them off to make certain y'all put them all back in the right social club.

Kickoff, you'll have the mounting assembly off your new disposal unit. To practise this, plough the LOWER mounting ring clockwise. This is the ring with the 3 tabs on it that looks only like the one y'all turned counterclockwise on your former unit in pace four above. This volition let yous remove the sink flange associates.

Next, you'll loosen the screws on the UPPER mounting ring. As seen in the picture show in a higher place, the screwdriver volition loosen the three screws. You won't remove the screws completely. You'll but loosen them.

So, you'll remove the snap ring. Use a flathead screwdriver to remove the snap ring past sliding the blade under the ring and lifting. See the top of the cooresponding image.

At present, every bit yous run across in the lower part of the image higher up, you lot'll remove the mounting ring (the band with the three screws in information technology) backup flange (shaped like a flower), and fiber gasket (the circular band correct above the flower-shaped ring) from the sink flange. Be sure to lay out these parts in the order you remove them so y'all tin can replace them in the right club. Feel free to snap a picture with your phone for reference, as well! Y'all tin always refer back to the image above or your motion picture if you think you might have gotten a office out of society.

Step three: Reassemble the mounting assembly

For this step, yous'll be working under the sink. Catch a flashlight so you take plenty of light (you can even use the one on your phone).

Place the fiber gasket (commencement, closest to the sink), fill-in flange (2nd), and mounting ring (3rd, closest to the floor) onto the sink flange. The cooresponding image will help y'all brand certain you have the pieces in the right social club.

At present, yous'll replace the snap ring to hold everything in place.

While you concur the 3 pieces up against the drain flange, open the snap ring and press it into the groove on the sink flange.

The terminal step is to tighten those 3 screws on the mounting ring. Exist certain to not over tighten them and tighten each 1 evenly.

At present—you're about there. Just a few more steps and your replacement garbage disposal will exist upwardly and running.

Step 4: Install the new discharge elbow

This is the step that gets the waste out of your disposal unit and sent downwards the drain, then this is of import. You don't desire to re-use your old belch elbow, either. Be sure to use the new one included with your new unit of measurement.

Make certain the rubber gasket is on the discharge elbow and slide it all the manner to the terminate that volition connect to the disposal unit.

Then, locate the mounting flange (shaped like a diamond with a circular hole in the middle). Slide the mounting flange upwards over the belch elbow and insert the discharge elbow into the unit of measurement, lining upwardly the mounting holes with the holes on the side of the disposal unit. Attach the discharge elbow to the unit of measurement by tightening the spiral on each side. Make sure the screws are tightened evenly and firmly, but don't over tighten. Refer to the image above.

If you don't have a dishwasher, you can skip step 5 and get straight to pace 6.

Stride 5: Knock out the dishwasher discharge plug (merely if you take a dishwasher)

If you have a dishwasher, you'll need to install the discharge hose on your new garbage disposal unit. To practice this, y'all'll need to knock out the plug that is mill-installed in your new disposal unit of measurement.

Insert a blunt object (like a steel punch or wooden dowel—exercise not use a screwdriver) into the plug and knock information technology out using a hammer. Apply kitchen tongs or pliers to reach into the disposal and recollect the plug. Throw the plug away.

Step 6: Connect your new garbage disposal to the mounting associates

You're almost in that location! Squeamish work.

From under the sink, align the newly installed discharge elbow on the side of your new disposal unit of measurement with the piping. Raise the new disposal unit up into the mounting band.

Side by side, locate the lower mounting ring (the one with the three tabs). Align the lower mounting ring with the ramps on the mounting band extending downwardly from under the drain. Turn the lower mounting ring clockwise until tight.

Then, grab a flathead screwdriver and insert it into one of the tabs on the lower mounting ring. This volition give you the extra leverage you demand to stop turning the lower mounting ring to lock it securely in place. Refer to the left side of the epitome below. The right side of the image shows how you can lock the lower mounting ring securely in identify by using channel lock pliers instead of a screwdriver.

Step 7: Connect the discharge elbow to the piping

Come across the cooresponding image for reference.

Be sure to tighten the connecters properly. Some will allow you to hand-tighten and others volition require that y'all apply a wrench to establish a secure seal.

Now, if yous don't take a dishwasher, you're all washed! Your new garbage disposal unit of measurement is ready to go. Before you turn the unit on, run water to make sure all of your seals are tight.

So, just head to your breaker box, plow the power back on, and and so plug your unit into the outlet underneath your sink.

Step eight: Attach the dishwasher discharge hose (but if y'all have a dishwasher)

As a reminder, this pace is only if you accept a dishwasher.

Connect the dishwasher drain hose that was attached to your erstwhile disposal unit to your new disposal unit. This will attach to the place where y'all knocked out the plug.

Slide the metal clamp on the dishwasher belch hose to the attachment point on the replacement garbage disposal unit of measurement and tighten the clamp using a screwdriver.

At present, for yous dishwasher owners, your replacement garbage disposal installation is consummate! Before turning the power back on, run water into the sink to make sure everything is seated properly and your seals are tight. And so, flip your excursion breaker back on, plug your disposal unit in, and test the unit.

Congrats on replacing a garbage disposal! With the included video and pace-by-footstep DIY guide, yous'll be a dwelling improvement pro in no time. Bask your spruced-up kitchen!

Featured Products

Now, for you dishwasher owners, your replacement garbage disposal installation is complete! Before turning the power back on, run water into the sink to make sure everything is seated properly and your seals are tight. And so, flip your circuit breaker dorsum on, plug your disposal unit of measurement in, and examination the unit.

Congrats on replacing a garbage disposal! With the included video and step-by-footstep DIY guide, you lot'll be a home improvement pro in no time. Relish your spruced-upwardly kitchen!

Source: https://www.moen.com/inspiration/kitchen/how-to-install-a-garbage-disposal

Posted by: batisteacesty72.blogspot.com

Share this post